[Click To Enlarge]
Email A Friend - Gift Reminder |
Dynamat 10455 Xtreme Bulk Pack 9 Sheets
Availability:
In Stock
Price:
$270.00
$104.66*
|
| Part No: | B00020CB2S |
| Manufacturer: | Dynamat |
| MFG Part: | 10455 |
| Customer Rating: | 4.5 / 5.0 |
|
|
- Kit Contains Nine 18 x 32 Piece of Dynamat Xtreme
- For General Use on Rear Decks Doors Floors and Trunk Floors
- Also Use for Trunk Lids Roofs Quarter Panels and Under-Hood Installations
- Get More Bass More Music Lower Road Noise and Better Sound
Dynamat 10455 Xtreme Bulk Custom Pak(TM) - Nine 18 x 32 Sheets 36 sq.ft. Total (1 Each)
|
1. Recived fast from
2. Did not think it take so long to add to my car, but I was wrong. It took upwards of 40 hours. I did the entire car. inside the car, trunk, and under the hood. I also bought a molded carpet with the extra rubber on the bottom of it.
3. I used truck liner spray under the wheel well.
4. Padded the license plate.
5. Bought the extra hood liner.
Total Cost: $720.00
For the exact same song I went from listening to that song at a vol of 25 because of the outside noise and the engin to 13 after words. The car now is quite with no rattle. Its great to get outside the car and listen to it. Just booms. No rattle. The muffler rattled a little, so I screwed it tighter. This stuff is amazing! I am pushing 2 4,000 watt amps to two 12" subs. this stuff really does work dispite what people say. Sure I think you could get it cheaper or make it yourself, but why, its made for you here and does the job! I did have lots of cuts on my hands and fingers after finishing this up. I did not need the roller. If its cold the stuff does not mold as easy, but if you heat it up with a blow dryer or heat gun it well go into place. I do not know how other people do it, but make sure to keep an eye out where the screws go because once it is on its hard to find. I ended up placeing screws in the holes then laying it over and pushing the screw through the Dynamat. Boom Boom Boom. not blah blah blah. |
| Can't tell if it worked in my Fit | 2010-02-19 | 4 / 5 |
|
| I put this in my 2007 Honda Fit Sport and I honestly can't tell if it made a real difference. Sure it seems like the road noise is duller. The wind sound isn't as harsh but did it actually improve anything? It sounds like it got rid of some of the higher pitched road noise but the low dull roar still gets through, which might just be because of the tires. I put it in my two front doors (doubled on the outer and inner panel) and the rear hatch door. I still have a bunch left so I might do more but it takes so long I don't know if it's worth it. The first door took like 3 hours until I got the hang of how to do it and how to get the doors off. I can't say this isn't a good product, it obviously does make a difference in the sound but I don't know if it really works in my car. I probably won't know until I get new tires since I still have the stock, which have been said to be obnoxiously loud. |
| Awesome. Great price. | 2010-02-19 | 5 / 5 |
|
| The Dynamat was easy to install and works great. For a typical interior including doors and trunk, you will need two bulk packs. |
| Freakin Amazing | 2010-02-18 | 5 / 5 |
|
This stuff really is all it's hyped up to be. I was a little hesitant when i first opened the package, seeing how thin it was. But it really works. I installed it first on my left rear door on my '08 Subaru Impreza. That door compared to the rest is unreal. Like everyone says, it makes the door feel more solid and valuable. As far as audio quality, I only have the stock speakers still, but there was a difference in bass response and clarity from that single speaker. It does not annoyingly resonate the door like it used to.
It did take a while to install it on the single door, but the rest should be faster since i have an idea of how to do it now. I read multiple installation guides, and they all said to pull off the plastic weather sheet and use it as a guide of how to cut the dynamat. THIS DID NOT WORK FOR ME. The plastic sheet does not sit snug against every curve of the door panel, so when i had used it as a guide, my dynamat sheet ended up being a bit small, and had to piece in some parts. Also, the holes in the plastic will not line up perfectly with your dynamat once you get it on the door since it is molding around all the curves. I cut the bottom edge first and the speaker hole, removed only the bottom edge of the paper backing, and worked my way up, cutting the needed holes as i went. Now it has a very clean look, but more importantly, a great sound. |
| wonderrful product | 2010-01-19 | 5 / 5 |
|
| I bought this to cover some areas that the original dynomatt buy didnt, and it performed much greater than i had ever expected it too. |
)
